PA6 – Polyamide 6 PA6-I GF30
AKROMID® B28 GF 30 S3 white (8349)AKROMID® B28 GF 30 S3 white (8349) is a 30% glass fibre reinforced, easy flowing polyamide 6. Furthermore, the material is impact modified and therefore characterised by a higher dry impact strength compared to standard PA 6 GF 30. Its high strength and stiffness make it the material of your choice for technical applications in industrial engineering and in the furniture industry. The material is colored similar to RAL9003.
Properties
Tensile Modulus Tensile Strength Impact StrengthFeatures
-
Mechanical Properties
Tensile modulus (1 mm/min | ISO 527-2) d.a.m. 8900 MPa
Stress at break (5 mm/min | ISO 527-2) d.a.m. 150 MPa
Strain at break (5 mm/min | ISO 527-2) d.a.m. 4 %
Flexural modulus (2 mm/min | ISO 178) d.a.m. 8200 MPa
Flexural strength (2 mm/min | ISO 178) d.a.m. 240 MPa
Flexural strain at break (2 mm/min | ISO 178) d.a.m. 4,5 %
Charpy impact strength (23°C | ISO 179-1/1eU) d.a.m. 94 kJ/m²
Charpy notched impact strength (23°C | ISO 179-1/1eA) d.a.m. 18 kJ/m²
-
Thermal Properties
Melting temperature (DSC, 10K/min | DIN EN ISO 11357-3) 220 °C
-
Flammability
Burning rate (<100 mm/min) (> 1 mm Thickness | FMVSS 302) +
-
General properties
Density (23°C | ISO 1183) 1,30 g/cm³
Molding shrinkage (flow | ISO 294-4) 0,1 - 0,3 %
Molding shrinkage (transverse | ISO 294-4) 0,5 - 0,7 %
-
Rheological Properties
MVR (275°C/5kg | ISO 1133) 31 cm³/10min
Flowability (1mm Thickness | AKRO) 130 mm
Flowability (2mm Thickness | AKRO) 450 mm
Processing information
The listed values are recommendations. Higher values should be used for higher glass loadings. We recommend only de-humidifying or vacuum dryers. Extensive drying can cause filling problems and surface defects.
 |
Drying time | 0 - 4 h |
| Drying temperature (τ ≤ -30°C) | 80°C | |
| Processing moisture | 0,02 - 0,1% | |
 |
Feed section | 60 - 80°C |
 |
Temperature zone 1 - Zone 4 | 240 - 290°C |
 |
Nozzle temperature | 260 - 300°C |
 |
Melt temperature | 270 - 290°C |
 |
Mold temperature | 80 - 100°C |
 |
Holding pressure, spec. | 300 - 800 bar |
 |
Back pressure, spec. | 50 - 150 bar |
| Injection speed | medium to high | |
| Screw speed | 8 - 15 m/min | |
Disclaimer
All specifications and information given on this website are based on our current knowledge and experience. A legally binding promise of certain characteristics or suitability for a concrete individual case cannot be derived from this information. The information supplied here is not intended to release processors and users from the responsibility of carrying out their own tests and inspections in each concrete individual case. AKRO®, AKROMID®, AKROLEN®, AKROLOY®, AKROTEK®, ICX® and PRECITE® are registered trademarks of the Feddersen Group.
