PA6 – Polyamide 6 PA6 GF30
AKROMID® B+ GF 30 6 black (7387)
Anorganic, high-heat stabilized PA6 compound with enhanced mechanical properties in conditioned state to substitute PA 66 compounds
Typical applications
Components in mechanical engineering and in the automotive industry
Processing information
The listed values are recommendations. Higher values should be used for higher glass loadings. We recommend only de-humidifying or vacuum dryers. Extensive drying can cause filling problems and surface defects.
Drying time | 0 - 4 h | |
Drying temperature (τ ≤ -30°C) | 80°C | |
Processing moisture | 0,02 - 0,1% | |
Feed section | 60 - 80°C | |
Temperature zone 1 - Zone 4 | 240 - 290°C | |
Nozzle temperature | 260 - 300°C | |
Melt temperature | 270 - 290°C | |
Mold temperature | 80 - 100°C | |
Holding pressure, spec. | 300 - 800 bar | |
Back pressure, spec. | 50 - 150 bar | |
Injection speed | medium to high | |
Screw speed | 8 - 15 m/min | |
-
Mechanical Properties
Tensile modulus (1 mm/min | ISO 527-2) d.a.m. 9500 MPa conditioned 6000 MPa
Stress at break (5 mm/min | ISO 527-2) d.a.m. 180 MPa conditioned 118 MPa
Strain at break (5 mm/min | ISO 527-2) d.a.m. 3,6 % conditioned 9 %
Flexural modulus (2 mm/min | ISO 178) d.a.m. 9200 MPa
Flexural strength (2 mm/min | ISO 178) d.a.m. 270 MPa
Charpy impact strength (23°C | ISO 179-1/1eU) d.a.m. 86 kJ/m²
Charpy impact strength (-30°C | ISO 179-1/1eU) d.a.m. 72 kJ/m²
Charpy notched impact strength (23°C | ISO 179-1/1eA) d.a.m. 14 kJ/m² conditioned 19 kJ/m²
Charpy notched impact strength (-30°C | ISO 179-1/1eA) d.a.m. 11 kJ/m² conditioned 11 kJ/m²
-
Thermal Properties
Temperature of deflection under load HDT/A (1,8 MPa | ISO 75) 210 °C
Temperature of deflection under load HDT/B (0,45 MPa | ISO 75) 218 °C
Melting temperature (DSC, 10K/min | DIN EN 11357-1) 220 °C
Coefficent of linear thermal expansion, parallel (23°C bis 80°C | ISO 11359-1/2) 0,19 1,0E-4/K
Coefficent of linear thermal expansion, transverse (23°C bis 80°C | ISO 11359-1/2) 1,14 1,0E-4/K
-
General properties
Density (23°C | ISO 1183) 1,35 g/cm³
Humidity absorption (70°C, 62% r.H. | ISO 1110) 1,9-2,1 %
Molding shrinkage (flow | ISO 294-4) 0,1-0,3 %
Molding shrinkage (transverse | ISO 294-4) 0,5-0,7 %
-
Rheological Properties
Flowability (2mm Thickness | AKRO) 480 mm
Disclaimer
All specifications and information given on this website are based on our current knowledge and experience. A legally binding promise of certain characteristics or suitability for a concrete individual case cannot be derived from this information. The information supplied here is not intended to release processors and users from the responsibility of carrying out their own tests and inspections in each concrete individual case. AKRO®, AKROMID®, AKROLEN®, AKROLOY®, AKROTEK®, ICX® and PRECITE® are registered trademarks of the Feddersen Group.
You have questions about our products?
With a worldwide network of plastics distribution experts, we can provide you with support anywhere in the world. Talk to one of our specialists to find out more.
CONTACT US NOW