PA6 – Polyamide 6 PA6 + PP GF25
AKROMID® B3 GF 25 1 L black (4637)AKROMID® B3 GF 25 1 L black (4637) is a PA6/PP-blend with reduced density compared to standard PA6 with 25% glass fibre reinforcement. The material is suitable for components with high strength and stiffness where cost and weight reduction are required at the same time. The chemical resistance of AKROMID® B3 GF 25 1 L black (4637) is particularly superior to calcium chloride (CaCl₂).
Properties
Tensile Modulus Tensile Strength Impact StrengthFeatures
-
Mechanical Properties
Tensile modulus (1 mm/min | ISO 527-2) d.a.m. 7500 MPa conditioned 5600 MPa
Stress at break (5 mm/min | ISO 527-2) d.a.m. 135 MPa conditioned 88 MPa
Strain at break (5 mm/min | ISO 527-2) d.a.m. 3,3 % conditioned 4,5 %
Charpy impact strength (23°C | ISO 179-1/1eU) d.a.m. 68 kJ/m² conditioned 58 kJ/m²
Charpy impact strength (-30°C | ISO 179-1/1eU) d.a.m. 67 kJ/m² conditioned 54 kJ/m²
Charpy notched impact strength (23°C | ISO 179-1/1eA) d.a.m. 15 kJ/m² conditioned 15 kJ/m²
Charpy notched impact strength (-30°C | ISO 179-1/1eA) d.a.m. 13 kJ/m² conditioned 10 kJ/m²
-
Thermal Properties
Temperature of deflection under load HDT/A (1,8 MPa | ISO 75) 198 °C
Temperature of deflection under load HDT/B (0,45 MPa | ISO 75) 217 °C
Melting temperature (DSC, 10K/min | DIN EN ISO 11357-3) 220 °C
-
Flammability
Burning rate (UL 94) 0,8mm Wall thickness HB Class
GWFI (IEC 60695-2-12) 0,8mm Wall thickness 750 °C 1,6mm Wall thickness 725 °C 3,2mm Wall thickness 750 °C
GWIT (IEC 60695-2-13) 0,8mm Wall thickness 775 °C 1,6mm Wall thickness 750 °C 3,2mm Wall thickness 775 °C
Burning rate (<100 mm/min) (> 1 mm Thickness | FMVSS 302) +
-
General properties
Density (23°C | ISO 1183) 1,22 g/cm³
Humidity absorption (70°C, 62% r.H. | ISO 1110) 1,5 %
Molding shrinkage (flow | ISO 294-4) 0,1 - 0,3 %
Molding shrinkage (transverse | ISO 294-4) 0,55 - 0,75 %
-
Rheological Properties
MVR (275°C/5kg | ISO 1133) 10 cm³/10min
Processing information
The listed values are recommendations. Higher values should be used for higher glass loadings. We recommend only de-humidifying or vacuum dryers. Extensive drying can cause filling problems and surface defects.
Drying time | 0 - 4 h | |
Drying temperature (τ ≤ -30°C) | 80°C | |
Processing moisture | 0,02 - 0,1% | |
Feed section | 60 - 80°C | |
Temperature zone 1 - Zone 4 | 220 - 290°C | |
Nozzle temperature | 240 - 300°C | |
Melt temperature | 240 - 290°C | |
Mold temperature | 70 - 100°C | |
Holding pressure, spec. | 300 - 800 bar | |
Back pressure, spec. | 50 - 150 bar | |
Injection speed | medium to high | |
Screw speed | 5 - 15 m/min | |
Disclaimer
All specifications and information given on this website are based on our current knowledge and experience. A legally binding promise of certain characteristics or suitability for a concrete individual case cannot be derived from this information. The information supplied here is not intended to release processors and users from the responsibility of carrying out their own tests and inspections in each concrete individual case. AKRO®, AKROMID®, AKROLEN®, AKROLOY®, AKROTEK®, ICX® and PRECITE® are registered trademarks of the Feddersen Group.